Jump to content

strath

Advanced Members
  • Content Count

    84
  • Joined

  • Last visited


Reputation Activity

  1. Upvote
    strath got a reaction from rossd in Replace frontrunner in cabin with?   
    I have Farr 1020
    A couple of years ago I to remove the front runner from the boat, finished up with plywood liner and a glue mess,.
    I then preceded to make panels that spanned across the full cabin ceiling and have them covered in vynal. This finished up a really nice job.
    The process 
    1/ I set out the panels to suit the width of the vynal and the position of any posts, or hatches, I started from the galley posts working forward, also to suit sheet of plywood, in this case they finish up approximately 550mm wide,
    2/ Having clean up the ceiling as best I could,
    3/ Using heavy brown paper, the type floor layer use, I made 550mm wide patterns, taping it to the ceiling making sure you start parallel to the bulkheads and scribing the ends,
    4/ I purchased 6mm plywood, which has a thick core that runs across the sheet, this makes it easier to bend to the curve of the cabin top.
    5/ I then laid the pattern on the paper and cut the first sheet.
    6/  I then fitted the panel into the boat holding them up by propping it up off the floor, you need a few props, as you must push the sheets up all the way across 
    7/  Then progressively making a pattern cutting the plywood and fitting each panel inside the boat, scribing the ends and side to match the previous sheet, the cabin top the curve changes and getting tighter as you go forward.
    8/ You need to allow 4-5mm clearance on the sheets ends and a 3mm space between sheets.
     9/ Once you have fitted all the sheets, sanded the edges and give them and small round.
    10/ This is where I cheated as I took the panels to the local upholsterer in Gulf Harbour where he covered the panels with 3mm foam sheets and then rapped them in vynal 
     The finished lookes great a slightly padded vynal panel.
    It was at the upholsterer recommendation I used 6mm plywood as he wanted wrapped the vynal around the edges to and use 100s of staples to fix on the back. Apparently you can not get shorter staples the 6mm. 
    The sheets are secured in place using industrial valcro stapled along all the edges of the panels and to the underside of the old plywood ceiling to match.
    It is a fiddly job but well worth the effort, having been a carpentry joiner a past lifeCeiling panels.msg helped.
    One of the benefits with the above system is that your can remove the panels to get to any bolts fixing turning blocks and deck gear.  
     
  2. Like
    strath got a reaction from ex Elly in Replace frontrunner in cabin with?   
    I have Farr 1020
    A couple of years ago I to remove the front runner from the boat, finished up with plywood liner and a glue mess,.
    I then preceded to make panels that spanned across the full cabin ceiling and have them covered in vynal. This finished up a really nice job.
    The process 
    1/ I set out the panels to suit the width of the vynal and the position of any posts, or hatches, I started from the galley posts working forward, also to suit sheet of plywood, in this case they finish up approximately 550mm wide,
    2/ Having clean up the ceiling as best I could,
    3/ Using heavy brown paper, the type floor layer use, I made 550mm wide patterns, taping it to the ceiling making sure you start parallel to the bulkheads and scribing the ends,
    4/ I purchased 6mm plywood, which has a thick core that runs across the sheet, this makes it easier to bend to the curve of the cabin top.
    5/ I then laid the pattern on the paper and cut the first sheet.
    6/  I then fitted the panel into the boat holding them up by propping it up off the floor, you need a few props, as you must push the sheets up all the way across 
    7/  Then progressively making a pattern cutting the plywood and fitting each panel inside the boat, scribing the ends and side to match the previous sheet, the cabin top the curve changes and getting tighter as you go forward.
    8/ You need to allow 4-5mm clearance on the sheets ends and a 3mm space between sheets.
     9/ Once you have fitted all the sheets, sanded the edges and give them and small round.
    10/ This is where I cheated as I took the panels to the local upholsterer in Gulf Harbour where he covered the panels with 3mm foam sheets and then rapped them in vynal 
     The finished lookes great a slightly padded vynal panel.
    It was at the upholsterer recommendation I used 6mm plywood as he wanted wrapped the vynal around the edges to and use 100s of staples to fix on the back. Apparently you can not get shorter staples the 6mm. 
    The sheets are secured in place using industrial valcro stapled along all the edges of the panels and to the underside of the old plywood ceiling to match.
    It is a fiddly job but well worth the effort, having been a carpentry joiner a past lifeCeiling panels.msg helped.
    One of the benefits with the above system is that your can remove the panels to get to any bolts fixing turning blocks and deck gear.  
     
  3. Upvote
    strath reacted to Black Panther in A new Film   
    Anyone know anything
     

  4. Upvote
    strath reacted in Anchoring technique FAIL   
    The bum of a 45fter, there abouts, spotting in a AKL yard this am.


  5. Upvote
    strath reacted in Ceramco for sale   
    Where is RB yachting? He loves an old Farr rating boat.....
  6. Upvote
    strath reacted to Kaihe Atamai in Gas bottle bracket & Spinnaker Bag for sale   
    I'd be interested in the bad if it's still available - I'll PM you.
  7. Upvote
    strath got a reaction from Island Time in Surplus yacht gear   
    Surplus gear, blocks, main boom outhaul track and traveller, fibreglass vent boxes etc.
    Make an offer for the lot or individual items. Some gear off a 1020.
     

  8. Downvote
    strath reacted to strath in Surplus yacht gear   
    Surplus gear, blocks, main boom outhaul track and traveller, fibreglass vent boxes etc.
    Make an offer for the lot or individual items. Some gear off a 1020.
     

×
×
  • Create New...