Jump to content

Fibre lifelines and Cat 3


Recommended Posts

Just thinking through lifeline options and was wondering if anyone had recently been through an inspection. Plan was to used single braid dyneema that is uv coated and as sleeves at major chafe points (stanchions and where headsails skirt) will this comply? Rules are clear as mud. I know KM has written about this a while back but was wondering if the safety inspectors had clarified it since ( I want to use the fine line dyneema braid).

Link to post
Share on other sites

https://chainsropesandanchors.co.nz/fibre-lifelines-what-to-use   here is the link to KM's think piece.   Fineline and others can and do make specific lifeline braids. Not sure why you would phaf around using a single braid with isolated sleeves. IMHO it would be better with a specific UHMPE double braid with both the cover and core being UHMPE - cover is  probably better with a UHMPE/technora blend. You can then put on specific chafe sleeves on top of this if necesssary.

Link to post
Share on other sites

Cost and ease of splicing are why I wanted to go the single braid route. Regs don’t specify single or double braid. I know overseas single braid is fine and that’s what my backstay is made out of so hoping it would be fine for lifelines. The local inspector says he thinks so. 
 

it’s pretty easy to lash on a sheath where it goes though staunchions.

Link to post
Share on other sites

1 2 3 4 5 LIFELINES 17.17 The minimum diameter lifeline wire shall be: X X X R R Yachts under 8.5m (LOA) 3mm Yachts 8.5m to 13m 4mm Yachts over 13m 5mm Wire manufactured with a plastic coating shall not be used. Grade 316 Stainless Wire is recommended – 1x19. Tape unacceptable. If fibre used instead of wire e.g. single braided dyneema, spectra, vectran, dynex or similar, there can be no tolerance for wear. Material must be protected from U.V. and chafe by a sheath. Sheath can be taken as an overbraided core over the main load member of the same material or another type of material. The strength of the fibre must be equal to or greater than that of the appropriate stainless steel wire. The wire shall show no significant signs of corrosion or weathering. When plastic tubing has been used it should be cut at its lowest point to allow any water to drain.

 

Not sure how the above permits a single braid without a sheath?

Link to post
Share on other sites

I think that’s where the inspectors get confused... the single braids which are mentioned in the Regs- have a uv coating. The local inspector said he thought that was sufficient to count as a sheath as long as chafe protection was sorted. But he wouldn’t commit until he saw the lifelines.

 

at half the price of super cable and still loads of strength figure it’s worth exploring.

Link to post
Share on other sites
On 23/08/2020 at 5:21 PM, TazzyDevil said:

I think that’s where the inspectors get confused... the single braids which are mentioned in the Regs- have a uv coating. The local inspector said he thought that was sufficient to count as a sheath as long as chafe protection was sorted. But he wouldn’t commit until he saw the lifelines.

I think that the spirit of the Regs is that the entire line should have a cover/sheath not just the points which you think might experience chafe.

Thinking back to a few kite drops that haven't quite gone to plan, I know that there is no part of my lifelines that has not had a rope dragged over it during its life.

On 23/08/2020 at 2:02 PM, TazzyDevil said:

Cost and ease of splicing are why I wanted to go the single braid route.

Class 2 core dependant splices are really easy. With 4mm I would probably stitch the cover to the outside rather than trying to tuck it.

Armare do a great lifeline that's YNZ approved. https://chainsropesandanchors.co.nz/5mm-Lumina-lifeline-Super-Cable

It has a dyneema cover so might not be core dependent, thus requiring a core/cover splice to get a close to full strength splice. KM confirmed this is core dependent.

On 23/08/2020 at 7:53 AM, TazzyDevil said:

Plan was to used single braid dyneema that is uv coated and as sleeves at major chafe points (stanchions and where headsails skirt) will this comply?

I queried this with Angus during an inspection, I  was told that the entire line had to be protected.

My plan, when I get to this project, is to get 4 or 5mm single braid dyneema into the dinghy fender covers and cover the exposed single braid with heavy duty heatshrink.  I have seen too many lines dragged over my lifelines to think that even a Dyneema cover would last more than a season.

Link to post
Share on other sites

The lifelines on Oliver are Dyneema "Supercable" from CRA (via SailIQ). 

They still look great after two years of regular use.  No sign of wear.  Being thin enough to pull through and remove the lifelines to repair stanchions is a bonus too.   

Recommend getting CRA, rigger or splicing specialist to splice at required length.  4mm Supercable is not an easy splice.  

Link to post
Share on other sites
Quote

Is a single braid OK from a actual in use point of view? Sure is when sized accordingly and the material it's made of is verifiable or you trust who you're shopping with. There are 'dyneemas', 'spectras', 'plasmas' being sold in NZ today that aren't, they are weak sh*t that looks roughly the same. There are some Chineemas being sold, some are OK but some are sh*t.

Apologies my UHMPE should have been  as per KM  -  UHMwPE  = Ultra High Molecular Weight Polyethyelene.   Interesting pre-stretching, heat treatment and solution dye versus dye bath issues also - there is huge variance as to UT strength and longevity - some are simply sh*t being sold as the bees knees.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...