Jump to content


  • Content Count

  • Joined

  • Last visited

Everything posted by candela

  1. Matt from Hurricane Rigging in Wellington is the importer. 027458471 matt@hurricanerigging.co.nz I have put the Grinder 40 onto my 1020 and am loving them. It is so wrong how fast the rope comes out of the winch. The videos do not do it justice. I have just ordered the compacts for the cabin top so will be interesting to see how they go for SSANZ.
  2. No I wasn't allowed to put a 1020 in a 30ft berth :(I am going down on Sat to do a hand over if you are around. No rush I can't see us getting out racing till after Xmas. My number is 0212237620
  3. We bought Strathspey. Hopefully with a bit if work we can get her up to speed Keen to talk about the genoa I'll give a call tomorrow.
  4. Any half decent Farr 1020 sails lying around?? Just bought a 1020 and would like to buy some sails to use for club racing. I have a good set but need something for cheap to use for club stuff.
  5. Thank you all for your replies. Sounds like they might be an interesting option for us. Just need sell Candela now
  6. Can anyone tell me what the difference is between a young 1034 and a young 99??
  7. Chris is a little disappointed but also like the idea of me not betting him not really sure what are going to get yet. Will see what is around if Candela sells. Fingers crossed
  8. It's not the one with the young 88 mast and the centre mounted engine is it??
  9. We have decided it is time for something bigger so Candela has gone on the market. http://www.trademe.co.nz/motors/boats-m ... 002767.htm If you are interested you can call me on 021 2237620
  10. candela

    simrad 2

    Both boats are back safe. Rafferty does not have rig standing up any more. Totally our bad we did not see them at all. Know they were around but the last cross they a lot further ahead and never thought we would catch that fast. We just clipped they back quarter with our prod but must have caught their back stay and pulled there rig down. I think we were really lucky they were not a little further back as I don't think a Whiting 29 going into the side of a Ross 780 would be very good at all. Rafferty did a great job of getting their boat sorted and I would like to send them my apolog
  11. I am looking for a heavy airs spinnaker for a whiting 29, luff about 11-12m, foot 5-6m. Though someone might have something tucked away in there garage. The last one I was offered is to small so but on the hunt for SIMRAD
  12. I have a Volvo MD7A, sail drive and bed, morse cables and lever and prop sitting in my workshop taking up to much space a the moment. It came out about a year ago. Was running fine when we pulled it out. We just decided with all the long trips we had coming up we would put a new motor in. Make an offer
  13. candela

    Your Prod

    I built this for Candela. Has worked really well even putting a code 0 on it with no bob stay. THe tube is from CTech and I have used a spinnaker beak to clip it to the deck. We bolted a stainless ring to the bow roller with nylon sleeve on the inside. Really easy to put on and off so still good for cruising. The tube was 72mm id tube with a 4mm wall tapped at each end and extra mm top and bottom to help with the code 0 loads. I have built 3 so far and all have had a trashing and not broken (cross fingers )
  14. Thanks fineline, I might have found something but Chris from Top knot a D28 will buy it. What is you number and I will get him to give you a call. Cheers
  15. I am looking for a heavy airs spinnaker for a whiting 29, luff about 11m. Though someone might have something tucked away in there garage
  16. Top Knot a Davidson 28 is looking crew for BOI Race week. He has just had a couple of people pull out at the last minute. Anyone keen can contact me and I'll put you in touch.
  • Create New...