Bad Kitty 252 Posted November 13, 2012 Share Posted November 13, 2012 Hard to say, & may never know. It looks like the deck under the main beam may have buckled? Was the rig tension much higher than before the refit? Also there is no continuity in a lot of the laminate at the break, almost looks like the main hull was built in 2 sections & joined at that point? Very sad, obviously a lot of work has gone in there in there since she arrived in country. As Scottie says though, it's not too bad to repair, best of luck boys, I'll try & get a bottle of Mt Gay down there once you get back into it! Moral Support that is! Link to post Share on other sites
Guest Posted November 13, 2012 Share Posted November 13, 2012 Well, proper Kiwi repair will do the job. I heard the boat went ashore or got badly damaged at Lac Leman ... and the repair looks like they were more concerned with outside surfaces - and piss poor finish at that. Also the rig is enormous, more than twice the length of the boat, which would set up some high loads. Have done a little research on what model Biscuits Cantreau - it is number 3, BC4 has a nearly squared off main hull stern. left to right: BC4, Full Pelt, BC3. Link to post Share on other sites
ScottiE 174 Posted November 14, 2012 Share Posted November 14, 2012 Hard to say, & may never know. It looks like the deck under the main beam may have buckled? I didn't see the bow section but - yeh - definitely something funny going on there as well. Given that the deck is dished to accept the beam, this area is effectively 'post-buckled' so that most of the direct compressive stresses are probably out at the gunwales anyway. If it failed in compression first I think the hull would have merely folded (ala the AC boat many years ago) and you'd see crumple zones in the gunwales. This looks to me like direct tension failure at the sole due to lack of material with the hull section remaining initially stiff until carbon layups really started letting go very quickly. I think this is the reason it looks so clean at the break so as to appear like it was two segments spliced together. Just my layman's view Link to post Share on other sites
Marshy 30 Posted November 14, 2012 Author Share Posted November 14, 2012 Just had a look and it seriously looks like there was a join there, and there is no tearing of carbon or anything. Must have been one hell of a bang! And such a perfect cut, you would have struggled to do nicer with a chainsaw! Link to post Share on other sites
Guest Posted November 14, 2012 Share Posted November 14, 2012 its very interesting with the continuity of the laminate and core around the break. it is probably more interesting to see the laminate movement ( read failire ) in the bulkhead just forward of the break. A term "tin caning" comes to mind having had a good external look at it. think rig tension and the canoe body centreline being under tension' then think a hindge point in way of the scollop for the forward beam then think if you stretch one you must compress another the bulkhead in the forwad portion of the main hull shows perfect signs of this to failure. then we go back to the continuity of the failure around the main (forward) beam bulkhead and think postage stamp Nothing a bit of a talk with a smart fox, a good boatbuilder and a grinder and green tape cant fix Link to post Share on other sites
Rental 1 Posted November 20, 2012 Share Posted November 20, 2012 Nothing a bit of a talk with a smart fox, a good boatbuilder and a grinder and green tape cant fix Also a grinder and a set of bog knifes. Link to post Share on other sites
Corley 0 Posted February 12, 2013 Share Posted February 12, 2013 Any news on the boat? Is the main hull being rebuilt? Sad to see that happen to such an amazing beast. Link to post Share on other sites
Guest Posted March 1, 2013 Share Posted March 1, 2013 Any news on the boat? Is the main hull being rebuilt? Sad to see that happen to such an amazing beast. Being rebuilt at Lloyd Stevenson Boat Builders by the new owner Link to post Share on other sites
diagobd2 0 Posted April 19, 2013 Share Posted April 19, 2013 Another picture, will be awesome to see it out! ___________________________________ SBB Key Programmervas 5054a Link to post Share on other sites
Recommended Posts
Archived
This topic is now archived and is closed to further replies.