Guest 000 Posted September 14, 2016 Share Posted September 14, 2016 I need a sail about the size of an Optimist sail for the little praam I'm building. I have a machine and a suitable floor and limited experience in sewing Sunbrella awnings for the H28. I'd like to have a go at sailmaking as it would be a good skill to have but don't want an expensive cock-up. Any one else done it? Quote Link to post Share on other sites
erice 732 Posted September 14, 2016 Share Posted September 14, 2016 apparently you can do a lot with white poly-tarp and double sided tape http://forum.woodenboat.com/showthread.php?162925-Polytarp-Sailmaking http://www.polysail.com/spritsail.htm though it would look a crime on your beautiful pram Quote Link to post Share on other sites
Guest 000 Posted September 14, 2016 Share Posted September 14, 2016 Thanks erice. I've read all that I can find on sailmaking and it doesn't seem to be too complicated. Mind you I did the same on carpet laying and the less said about that little exercise the better! I guess what I need to know is has anyone read a book, built a sail and the end result was not too bad. Quote Link to post Share on other sites
wheels 543 Posted September 15, 2016 Share Posted September 15, 2016 Hey, it's a bit of cloth, Scissors and a Sowing machine. Cut in general shape and sow hems. Can't be too hard eh Chris. Just think, learn how on the pram sail and then you can set up shop and become a sail maker. A whole new career. Quote Link to post Share on other sites
Guest 000 Posted September 15, 2016 Share Posted September 15, 2016 Theoretically. Do you use double sided tape to assemble the panels before stitching? If so, how do you stop the adhesive transferring to the needle, and does it matter? How do you match stitch tension to Dacron stretch? How do you calculate seam curvature for sail shape? I think sailmaking is a bit more complex than it appears. But, picking up some 4oz Dacron on Tuesday so I'll either end up with a sail shortly thereafter or yet another magnificent cock-up. Hoping strenuously for the former. Quote Link to post Share on other sites
SloopJohnB 322 Posted September 15, 2016 Share Posted September 15, 2016 You could get technical and use blocks to get the shape as its done on IOM sails. http://www.onemetre.net/Build/Sailmake/Sailmake.htm http://www.rcsails.com/sailmaking.html Quote Link to post Share on other sites
B00B00 310 Posted September 15, 2016 Share Posted September 15, 2016 Theoretically. Do you use double sided tape to assemble the panels before stitching? Yes, go and see kent Luxton (asuming you are able to get to picton) he will sort you out If so, how do you stop the adhesive transferring to the needle, and does it matter? Only really maters if you are doing really long seams then you ahve to clean the machine regularly How do you match stitch tension to Dacron stretch? Run the sticthing as loose as possible. Shouldnt be an issue with 4oz dacron. How do you calculate seam curvature for sail shape? totally depending on the type of sail. I would be putting about 15-20mm in over 3 seams to start with. the luff curve is also very important to the shape I think sailmaking is a bit more complex than it appears. But, picking up some 4oz Dacron on Tuesday so I'll either end up with a sail shortly thereafter or yet another magnificent cock-up. Hoping strenuously for the former. Im down in Waikawa and Nelson next week if you want me to bring something down for you. For the edges I would be just doing a 30mm turnover rather than adding a tape but you will need a rope up the luff . for the eyelets int he corner you are best to go to someone and get them to put them in. the tools needed are quite expensive. Quote Link to post Share on other sites
RushMan 31 Posted September 15, 2016 Share Posted September 15, 2016 BooBoo... Could webbing loops be used instead of eyelets? Quote Link to post Share on other sites
Guest 000 Posted September 16, 2016 Share Posted September 16, 2016 Thanks for the replies. Attached the sail dimensions from the plans. As you can see, its pretty small. I think I'm ok with the actual construction of the sail - what I don't know is how to build in a shape, if its even necessary on such a small sail. For example, do I make the sail totally flat but put a little curvature along the foot to induce a bit of fullness, or does each seam have to be a little curved? I'm sure the luff would be straight as its not attached to the mast, and the leech is self explanatory but what about the yard - would that seam be straight? Like everything, once you look a little deeper it becomes more complex. Quote Link to post Share on other sites
Battleship 100 Posted September 16, 2016 Share Posted September 16, 2016 Listen to Booboo he's the resident expert, my thoughts would be that you definitely need shape unless you never need to sail upwind. Quote Link to post Share on other sites
waikiore 409 Posted September 16, 2016 Share Posted September 16, 2016 good to see you are going for a superior Lug, the best rig for a dinghy Quote Link to post Share on other sites
eruptn 97 Posted September 16, 2016 Share Posted September 16, 2016 Check out software like this: http://www.sailcut.com/ Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.