Marshy

So i know about the BEP model - but what are other people using? Are there any decent alternatives. Ideally looking for an LPG sensor and switch in one unit, but otherwise just the LPG Switch would do. Fire away...

Haha yea i saw it pop up and recognised it from a while ago. Maxi Yacht Rolex Cup 2011

Yeah it probably was - it was from September 2011 Big crash though

I would go and negotiate with the Ross 780 guy and see if you can pull the price closer to the Trojan price. - In my opinion a far better boat. The outboard age alone is worth the price difference - a new outboard is not a cheap exercise...

Get hold of Rick at KZ Marine and buy some of the nice plastic Forespar ones - they aren't expensive. and then transfer them into the new carbon pole... Nige - flick me a text and i will pass on the details. 021 746 129

Link was on the first page.

The new motor we put in Cosa Nostra has a banjo fitting as the sump plug which has a hose that runs off to a manual pump. So basically an extraction pump from the sump plug - would be easy to retro fit into existing motors but makes Oil change a breeze... Lombardini LDW1003m

And my what a good reach it was - Love that Gennaker! - (And for the first time i didnt make the advert) - Its more a poster boat for PIC Insurance who is the primary sponsor of the event... SJB - Yes thankfully it shifted and became a reach all the way up the coast - no beating involved in that coastal

Tamaki Strait...

We can do a Cat division no problems at all if we can get interest from 5 boats? Entry form here -http://www.bbyc.org.nz/data/uploads/nor-winter-2016.pdf $20 for the two race days.

Listed on Trade-Me, but dues to Matt if it sells via here. Contact me on 021746129 Cheers Marshy

Young 88 - Mk2 - Cosa Nostra http://www.trademe.co.nz/Browse/Listing.aspx?id=1121560038 Cosa Nostra – A fantastic cruiser with a proven race record to match. New Lombardini 30HP installed October 2015 along with new Sail drive and new Gori folding Prop - Cruises at 7.5 knots with HP to spare for that pesky south westerly! New Engine Beds, New Engine box, and all new Engine sound proofing make for quiet and smooth motoring. Standard Mk2 Layout with extra deep cockpit locker – great for storing fishing / boating gear. Squabs and interior in great condition. Including a fill in and s

Quick trip to a lake or River and dunk in fresh water it is the best way!

yeah they can be sleeved fine. My advise would be to talk with Bart - or else get hold of Grunta McKinnon - he just did it with what looks like the same mast section for the Smoke Wagon mast - and as everyone know Grunta is the Carbon guru... Get in touch with me Nige if you havent got his details. or http://windwarrioryachts.co.nz/

Whats that? You want more speakers??

dont tell any raceboat owners wife that or the country will run out of heatguns and clamps!!

I can check with FOC but i think they were Durapox'd to start with - so a light sand back and re-coat...

The Navtec agent in NZ is Kiwi Yachting http://kiwiyachting.co.nz/content/navtec Blair / Gappy will help you out. Otherwise if thinking ENZED type Hydraulic man in a van type - give Neil a call - 027 473 4457 - He owns the Ross 930 Lightfoot, and an ENZED franchise. And is a good rooster that knows his stuff. He did quite a bit of Hydro work for us when i was rigging.

Nah not me! He stole my name for his email address cheeky bugger!

Take on? Or dream about then put in the back yard to pop up on trade me again in a few years time when that wife got sick of it

Cable ties are heaps easier...

Not that one no, through some miracle given how hard it was pushed!

What do you mean - Boats are a fantastic investment arent they?

Problem is loads on a prod are not 2 dimensional or in a single plane, they are up, and across, so the load is all over the place, sort of the same with a mast. But the Round Tube handles the load on all quadrents equally as well. It would be easier to kink a triangle if the bending point was on the flat portion...

That would be the Harbour Master then!